Project Wood Working

The Unplugged Summer

Thanks for waiting.

Back in the city after an incredible summer out on the coast. Im really quite excited to be getting back to work on the heritage door project but before I do I thought Id share a little slice of the past seven weeks at home on Cape Breton, in my nice, sunny wood shop. A few quick projects and the hurdles along the way. This blog process reminds me of children starting a new grade in school...remember your teacher asking you to stand up in front of the class room - strange new faces staring, palms sweating grasping empty handfuls of air...
"Tom, why dont you tell the class what you did on your summer vacation this year?"
Let there be light!

















6:15 am...Early July My bench room all clean and tidy; almost empty save this early morning sunshine rolling into the work space. Slowly rising, calmly creeping up from behind the hill behind our home. Ive been browsing around the woood shop determined to find some forgotten gem in an off cut pile. This is what inspires, no design in mind but a staggered stroll, cutting and shaving through the wood fiber. I found a nice plank of Khaya, (a kind of modern Mahogany substitute) still on the wood rack; must have been an off cut from the boat building days. I think this 4/4 plank, (1") was left behind because it seemed to have a bit of rot and some disturbing checks in the end grain. Definetly unsuitable for anything sea worthy but fine for a relaxed project without any boundaries here in this summer shop atmosphere. This doesnt bother me, the quality of the wood. I have no reservations or expectations...I knew Id be working with off cuts and reclaimed wood this summer so I decided to move ahead and work with it. At this point in the game I had only a dovetailed box in mind, perhaps something to store my water stones in? Although Im on vacation, I need to keep up the hand skills and what better project than a simple dovetailed box, made by hand from plank to plane this is as good as it gets. The plank was run through a thickness planer a few years ago and has been sitting ever since. Not the prettiest piece of wood around but the largest off cut I could find for my practice/vacation project. Here goes...

















So first things first, you may notice in the shot above that my tool chests chock full of hand tools made the 22 hour drive and my second, slightly damaged work bench never left this place last year when we moved; but an over sight I quickly find is my saw bench...you know, the Schwarz special I use day to day...2500 kilometers away in my basement shop in Toronto - damn. Ill make do with what I have; a scrap yard chair as old as Methuselah its been held together with duct tape and good wishes for as long as I can remember. A saw bench it isnt except when it is...and on this early morning in July it had to be just that. My trusty old Corporate Kangaroo to rip an edge and a few moments later...



The plank is ready for the vise and the plane work begins. In this next shot you can see the small level I use when I place any work piece in my shoulder vise; a quick and easy little trick to insure youre always working level in the vise. I paid pennies for it a while back and it now travels with me, one of my hand tool essentials in the Cabinetmakers Tool chest.

















My 5 1/2 Jack will scrape away the scars left behind from the hand saw and soon enough Im onto the opposite edge. Repeating these steps like a familiar dance, a perfect world would see my toolbox being infinite and Id be able to travel with my large jointing plane and all of my hand tools...but the reality is we have two young children, a dog and a not so large SUV. My jointing plane stayed behind so the 5 1/2 is the big gun today. I dont mind using this plane for edging boards. Remember, Im not jointing here but dressing the edges and the Jack plane is ideal for this scale of work.



Now with the two edges dressed Ill move onto an end, to square it up and continue along the process. Again I need to laugh and take two steps back before I can move on because my shooting board is with my saw bench and all of the stink I left behind in Toronto. A quick browse through the off cut isle and I get to work on a simple shooting board.















No side ramps or fancy bells or whistles but a bare minimum bench hook that will do the job well. David Charlesworth uses this simplified jig and who really in their right mind would argue with him? 20 minutes at best and Im taking practice shavings. The surface is 3/4" walnut plywood; I didnt change the size its the size it was left at and itll work out fine. The hook on the front underside is also plywood with an off cut of hardwood for the fence.

















Seems to work fine but the bench top needs some fixin. Again Im humming the blues trying to walk before I crawl; the bench top is anything but flat so Ill need another hour before I start squaring up the plank. If youre a frequent reader here you may have watched me flatten my bench top this past Spring in Toronto...well here I go again so Ill try not to ramble on too much about it. (not bloody likely) This bench was damaged in delivery when I purchased it and it always served as a sharpening station with extra real estate for furniture components while I worked at my other bench. (the one thats with me in Toronto) No surprise that it needs to be dressed seeing as its been sitting here in an unheated wood shop for a few years now...

















With the new shooting board working and safely tucked away below I begin the process of flattening my bench. Not too much grief over-all but the tail vise is pretty messed up. I use this vise the very least in my shop, instead relying on simple bench stops for hand planning and my front shoulder vise for 90% of the clamping load.






















getting there...






















Complete and clean with some shavings for the garden... Now then, with a side step or two I can get back to work on the little box design Im seeing in my mind, a rough sketch on an off cut and were ready to start dimensioning the components. The bench top is flat and the shooting board is working. Ill lay-out the lengths for the four sides to begin. A marking gauge or panel gauge is the tool for the job and Ill show you why I prefer using the panel gauge over the marking gauge for any measurements over a few inches.






















This is the Lie-Nielsen panel gauge and a Tite-Mark by Glen Drake, probably the most used tool in my shop and the nicest marking gauge Ive ever used. Perfect for dovetails or any joinery under 3". Once you get past that 3" mark I find the round plate area of the gauge a little small to hold with any accuracy while marking a line like the example given here. Before I had a panel gauge Id simply measure with a rule and stike the line with a knife but I find I get better results with a gauge referenced off of the freshly squared end off of the shooting board. The panel gauge on the other hand with its large surface to reference is both comfortable and accurate.






















With the panel gauge set and the cutting knife adjusted to the proper depth Ill begin the line making sure to keep my hand pressure on the front leading edge. I travel across the board transfering my grip and roll my hand position over to the back side of the gauge as I finish off the line. This movement feels natural and keeps the fence tight to the work edge. The next three shots will show the positions.


























First line cut crisp and square Ill get out my cross-cut panel saw and working off of the end of my work bench get the pieces ready for joinery.















A top and a bottom with two sides, a few minutes to complete its back to the Jack plane to surface and shoot making two pairs as close as I possibly can. A simple box, four sides-only a few minutes right? You can see that in a hand tool shop that sometimes the getting started and setting up stages can take a little longer but we wont need to do this all the time.














So the bench top is flat and Ive made a new shooting board (and a bench hook but I didnt take any shots...its pretty much the same as the shooting board with a thinner fence stock) I can move ahead with the project and work comfortably and efficiently. A simple morning set-up and the Unplugged Summer Shop is ready to go...or is it? Im beginning to plane the surfaces but before I do Ill need to make a bench stop. Another small delay in this mornings routine but the journey is the destination and this is the joy of working wood with hand tools. More to come... Cheers!